How to Change The Endplate on an AR-15!
How to Change The Endplate on an AR-15!
In this video, I show you guys how to change an endplate on an AR-15. A reminder that I don’t know if I mentioned it enough in the video, you should always make sure to stake your castle nut.
Hunter’s Channel:
https://www.youtube.com/channel/UCWG2ba_Nc4jvvyadaxdBbug
Jared’s Channel:
https://www.youtube.com/channel/UCOvtAZZx2qw71tqUdXVovvA
Camera Gear that I use!
Glide Gear GG 665 Tripod (Camera or Rifle) – https://amzn.to/2HdWs9K
Go Pro Hero 7 – https://amzn.to/2Zc5dao
Canon T7i – https://amzn.to/2Iv5EHv
Canon 18-55 Lens – https://amzn.to/35eoMTK
My Favorite Outdoor and Shooting Gear:
↦VORTEX CROSSFIRE 4×12 – https://amzn.to/31PiMi6
↦ Leupold RX-1300i Range Finder – https://amzn.to/2Hd9wfx
↦ Walker Headphones – https://amzn.to/2pW7afm
My Favorite Predator Hunting Gear:
↦ FoxPro – https://amzn.to/31Plqo2
↦ Windfire Red and Green Light 46$ – https://amzn.to/2ojrs1X
** Affiliate Links **
EMAIL ME!
↦info@takesomeoneoutdoors.com
Social Media Links:
↦ Instagram: https://www.instagram.com/elliott_delp/?hl=en
↦Twitter: https://twitter.com/elliott_delp
↦ Facebook: https://www.facebook.com/elliott.delp
***IMPORTANT DISCLAIMER***
I AM NOT A GUNSMITH, NOR DO I CLAIM TO BE. I DO NOT SELL FIREARMS. ALL THE INFORMATION THAT IS RELEASED ON THIS ACCOUNT IS INTENDED TO BE EDUCATIONAL AND A SOURCE OF ENTERTAINMENT. ANY TYPE OF IMITATION OF THE ACTS ON THIS CHANNEL WILL BE AT YOUR OWN RISK!
Any reason why you need to take the stock off?
to stake the castle nut, you use a punch and hammer to push some metal from the endplate into the designated notch on the castlenut.
https://www.youtube.com/watch?v=aCWDT1B_EIk&ab_channel=T.REXARMS
Is that buttplate Rubber? Will it work with CTR Stock?
Quality
what do you mean by staking your castle nut?
Great video thanks for the help
I’m willing to bet you scuffed your left hand on the top rail unscrewing the delta ring, didn’t you?
I only say this because I just did the same thing today 🤫
Ggggah! as in buffer Springgggah or one point Slinggggah.
Thanks chief! I built my ar a while ago, so I forgot about that spring beneath the end plate. Would’ve lost that without the reminder lol
What is the tool you used to tighten the castle nut?
Where did you get your stock from?
How far to screw in the stock tube? Until it stops or is there a set depth?
"I highly recommend you stake the castle nut"…."but I don’t know how to do that". Then why would you recommend that?
Great job on the take down and installation of the end plate. I have 4 AR’s that I will be replacing endplates on today. Thank you again.
My AR has the same end plate. Idk why they don’t just put the qd end plate on all. Cool vid.
Great video. thanks.
Tip for depressing the buffer spring retaining pin. Push the spring back with your thumb and use the tip of a bullet to push it down. Trust me, easier and less painful than pushing it down with your finger or nail.